|
|
| (129 intermediate revisions by 3 users not shown) |
| Line 1: |
Line 1: |
| = Exosuits =
| | Test |
| Construction of exosuits are restricted by ID, so they are typically the product of [[roboticist]]s and the [[Research Director]]. These can be tremendously helpful or tremendously annoying depending on who uses it. They take more work to make than robots and require special circuits, which are obtained through the [[Quartermaster]] or the Research and Development console.
| |
| | |
| Exosuits are wholly modular, meaning what you make can (mostly) be mixed and matched to create whatever vehicle you desire. From chicken-legged brawling mecha to tread-based taxis, the possibilities are endless.
| |
| | |
| The current list of exosuit parts is as follows.
| |
| ==Exosuit Construction==
| |
| <div class="toccolours mw-collapsible mw-collapsed" style="width:99%">
| |
| ===[[File:Mechframe.png]] The Frame===
| |
| | |
| The backbone of the mech itself, this can be modified at any stage of construction.
| |
| <div class="mw-collapsible-content">
| |
| | |
| To finish:
| |
| * Apply 15 steel sheets to the frame.
| |
| * Wrench the steel sheets in place.
| |
| * Weld the steel sheets in place.
| |
| * Wire the frame.
| |
| * Wire cutters to neaten the wiring.
| |
| * The following is the limitation and requirement for the frame's finished parts :
| |
| * - Motivators
| |
| * - Sensors
| |
| * - Manipulators
| |
| * - Chassis
| |
| * Once it's all applied, screwdriver to complete.
| |
| </div></div>
| |
| <div class="toccolours mw-collapsible mw-collapsed" style="width:99%">
| |
| ===[[File:Robotarmor.png]] The Parts===
| |
| | |
| The actual defining features of the mech, appearance and performance wise.
| |
| Each part has unique attributes that make them superior or inferior to the other parts, depending on situation.
| |
| <div class="mw-collapsible-content">
| |
| Individual parts of the mech require various, smaller parts from the mech fabricator to finish. Robot parts are found under the "robot" tab specifically, not the exosuit tab itself.
| |
| | |
| To finish the '''motivators and manipulators''':
| |
| * Apply one robot actuator.
| |
| | |
| To finish the '''sensors''':
| |
| * Apply one robot camera.
| |
| * Apply one robot radio.
| |
| * Apply one ''exosuit control module'', this is among the most important parts of the mech. Details are in "The Details" section below.
| |
| | |
| To finish the '''chassis''':
| |
| * Apply the exosuit armor of your choice. This is very important as it judges the durability of your mech.
| |
| * Apply one power cell of your choice.
| |
| * Apply one robot diagnostic unit.
| |
| | |
| | |
| * Once it's all done, place the parts on the mech frame.
| |
| </div></div>
| |
| <div class="toccolours mw-collapsible mw-collapsed" style="width:99%">
| |
| ===[[File:Robotradio.png]] The Details===
| |
| | |
| The specifics on each frame available to robotics.
| |
| <div class="mw-collapsible-content">
| |
| | |
| [[File:ModularAPLU.png]] * '''Powerloader''' - Parts for an industrial-grade power loader. The modular mecha adaptation of the APLU "Ripley," tends to be utilized for mining and heavy lifting.
| |
| | |
| | |
| | |
| </div></div>
| |